Injection molding production is the last step of molding injection molded parts. Before injection molding processing and product…… MORE
At present, there are six trends of modified plastics for household appliances. It mainly includes: brighter appearance color \ …… MORE
療器材類/美容儀器殼8.jpg)
1、外觀和用料 外觀和用料是一個醫療器械外殼的基本上的特點，外觀直接決定了一個外殼能不能被客戶接受的首要標準，所以現階段的外觀也逐漸偏重多樣化發展趨勢，因而在我們的測試中也占有一定的比重。用料關鍵取決于醫療器械外殼廠家選用的材料，醫療器械外殼的邊緣是否經過打卷處理，材料的好壞也會影響到防電磁輻射性能。 ……
MORE
塑膠外殼注塑成型的解鎖模具很容易產生振動，對機器的壽命和穩定性影響很大。因此，在調整塑膠外殼解鎖模具的時候，請注意以下的事項：慢速開啟速度是模具的啟動速度，所以速度低于中速，一般使用慢速中壓。因?yàn)槟０逶阪i緊的過程中有一定的變形產生夾緊力，所以啟動壓力可以適當高一些，一般在50%左右。慢位看型號而定，一般在塑膠外殼的模具……
MORE
鋁外殼在社會上應用的范圍較為廣泛，使得這種產品在市場上的銷量相對比較高。但是客戶在選購鋁外殼的時候，需要參考一定的標準，這樣使得選購工作才可以更加順利的進行。 客戶在鋁外殼進行選購工作的時候，可以按照產品的質量來進行選擇，質量的好壞會對其使用時間產生很大的影響。同時，質量良好的產品在使用的時候效果比較好，……
MORE
Lack of glue, also known as insufficient filling, is one of the common problems in the process of injection molding. The injecti…… MORE
In the process of injection molding, some carelessness will often cause defects in plastic products, which will affect the effic…… MORE
In fact, the common processing of the power supply plastic shell mainly includes the female mold with variable cavity composed o…… MORE
Spraying coatings of common colors on the plastic shell can enrich the color of the plastic shell, meet the needs of different c…… MORE
In the injection molding industry, the plastic shell has a certain shrinkage after molding, which will be analyzed from four asp…… MORE
As we all know, temperature is a very important factor in the whole process of the injection molding factory, and its level will…… MORE
我們?cè)诩庸に苣z外殼的時候，經常會出現一些問題，其中之一就是開裂。眾所周知，開裂的主要原因是應力變形，而應力主要可以分為殘余應力、外部應力和外部環境引起的應力變形。因此，要解決塑膠外殼加工中的開裂問題，注塑模具廠需要從解決應力入手。 1、殘余應力引起的開裂 殘余應力主要由以下三種情況引起，即過充、脫?！?/p> MORE
備/監控器3.jpg)
療器材類/假牙清潔器殼.jpg)
殼2.jpg)
類/掃地機殼2.jpg)
殼10.jpg)
