丰满少妇被猛烈进入无码,国产精品亚洲欧美在线播放操,无遮挡又黄又刺激又爽的视频,久久久久亚洲AV成人

Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

News



Tel:(0755)27151698
Fax:(0755)27150611
Mailbox:szzyzcl@163.com / szzy@szzy99.com
Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
Industry information

當(dāng)前位置:

首頁 News Industry information

Cause analysis and solution of plastic shell dent

Release time:2022-02-28

During the injection molding process, the dents of the plastic shell are shrinkage dents generated after the plastic is cooled and hardened, which mainly appear in the thick wall of the plastic shell, ribs, shell, nut insert back, etc.

3.jpg


1、 Equipment:

(1) Insufficient feeding

The screw or plunger is seriously worn, and the molten material leaks during the injection and pressure maintaining process, which reduces the mold filling pressure and the amount of molten material, resulting in insufficient molten material.


(2) Nozzle hole too large or too small

If it is too small, it is easy to block the sprue; if it is too large, the injection force is small, and it is difficult to fill the mold.


2、 Mold:

(1) The gate is too small or the runner is too narrow or shallow, the runner efficiency is low, the resistance is large, and the molten material is cooled too early.

The gate cannot be too large, otherwise the shear rate will be lost, the material viscosity is high, and the plastic shell will not be full. The gate should be opened on the thick wall of the plastic shell. By setting up a cold charging well with sufficient capacity in the flow channel, the cold charging can be excluded from entering the mold cavity, so that the mold filling can continue.

The gate length of point gate and needle gate must be controlled below 1mm, otherwise the plastic will solidify rapidly in the gate, affecting the pressure transmission; If necessary, increase the number of point gates or gate positions to meet the actual needs; When the flow passage is long and thick, exhaust grooves should be set at the edge of the flow passage to reduce the blocking effect of air on the flow of materials.


(2) Multi gate mold should adjust the filling speed of each gate, and it is best to set up gates symmetrically.


(3) The key parts of the mold should be effectively set with cooling channels to ensure that the cooling of the mold has a good effect on removing or reducing shrinkage cavities.


(4) The whole mold should be free of burrs, have reliable mold closing tightness, and can withstand the filling of high-pressure, high-speed, low viscosity molten materials.


3、 Technical aspects:

(1) Increase the injection pressure, maintain the pressure and prolong the injection time.

For plastic with high fluidity, high pressure will cause flash and collapse, so the material temperature should be appropriately reduced, and the temperature of the front of the barrel and the nozzle should be reduced, so that the volume change of molten material entering the cavity is reduced, and it is easy to cold solidify; For high viscosity plastics, the barrel temperature should be increased to make it easier to fill the mold. When the gate area shrinks, the pressure holding time should be extended.


(2) Increasing the injection speed can easily fill the parts and remove most of the shrinkage.


(3) The thin-walled plastic shell should increase the mold temperature to ensure the smooth flow of materials; The thick wall plastic shell should reduce the mold temperature to accelerate the curing and shaping of the skin.


(4) The cooling residence time of the plastic shell in the mold is prolonged, the production cycle is kept uniform, the back pressure is increased, and a certain buffer pad is reserved at the front end of the screw, which is conducive to reducing the shrinkage phenomenon.


(5) The low precision plastic shell should be taken out of the mold as soon as possible and cooled slowly in air or hot water, so that the shrinkage depression can become smooth without affecting the use.


4、 Raw materials:

The raw material is too soft and easy to flow. The effective way is to add nucleating agent to the plastic to accelerate crystallization.


5、 Plastic shell design:

The design of plastic shell should make the wall thickness uniform and try to avoid the change of wall thickness. For plastics with large shrinkage such as polypropylene, when the thickness changes by more than 50%, it is best to replace the thickened part with ribs.

Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
日韩中文字幕v亚洲中文字幕-日韩亚洲av免费在线观看| 色婷婷六月婷婷一区二区-91草草国产欧美在线观看| 色婷婷六月婷婷一区二区-91草草国产欧美在线观看| 欧美一级二级三级在线看-日韩精品欧美嫩草久久99| 亚洲欧美激情自拍色图-国产亚洲精品sese在线播放| 日韩亚洲欧美综合在线-成人在线网站在线观看| 国产aa视频一区二区三区-国产精品久久久久久久毛片动漫| 国产在线不卡高清一区-日本一区二区三区四区无卡| 久色高清精品在线国产-国产精品视频一区三区四区| 国产在线不卡高清一区-日本一区二区三区四区无卡| 亚洲产国偷v产偷v自拍性色av-亚洲欧美日韩国产三区| 日韩精品亚洲不卡一区二区-成人网在线视频精品一区二区三区| 欧美一级二级三级在线看-日韩精品欧美嫩草久久99| 亚洲愉拍自拍欧美精品app-亚洲一区不卡在线视频| 精品亚洲卡一卡2卡三卡乱码-一区三区二插女人高潮在线观看| 亚洲女人黄色录像一区-日韩av电影在线免费看| 亚洲国产欧美日韩不卡-熟妇激情一区二区三区| 黄片一区二区三区在线看-偷拍一区二区在线观看| 中文字幕偷拍亚洲九色-亚洲视频不卡一区二区天堂| 看肥婆女人黄色儿逼视频-秋霞电影一区二区三区四区| 亚洲国产精品日韩欧美-国产又粗又硬又大爽黄| 日韩av电影一区二区网址-老熟妇仑乱视频一区二| 91麻豆免费在线视频-欧美中文天堂在线观看| 日本女优一卡二卡在线观看-欧美大胆a级视频秒播| 女主播啪啪大秀免费观看-精品99午夜福利影院| 天天干天天日天天射天天舔-精品香蕉视频官网在线观看| 91精品国产影片一区二区三区-欧美精品久久久精品一区二区| 亚洲欧美精品在线一区-99热国产在线手机精品99| 97一区二区三区在线-欧美护士性极品hd4k| 国产欧美一区二区三区嗯嗯-欧美一区二区日本国产激情| 国产成人精品亚洲精品密奴-国产成人AV无码精品| 交换朋友的妻子中文字幕-日本美女8x8x8x8| 婷婷六月视频在线观看-久久亚洲综合国产精品| 亚洲av综合av一区东京热-黄页免费视频网站在线观看| 亚洲欧洲成视频免费观看-国产福利一区二区在线观看| 欧美日韩黑人在线播放-51在线精品免费视频观看| 欧美日韩亚洲1区2区-黄污视频在线观看不卡| 欧美aa一级视频播放-久一一区二区三区大香蕉| 免费午夜福利在线观看-黄色日本黄色日本韩国黄色| 日本女优一卡二卡在线观看-欧美大胆a级视频秒播| 欧美aa一级视频播放-久一一区二区三区大香蕉|