丰满少妇被猛烈进入无码,国产精品亚洲欧美在线播放操,无遮挡又黄又刺激又爽的视频,久久久久亚洲AV成人

Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

News



Tel:(0755)27151698
Fax:(0755)27150611
Mailbox:szzyzcl@163.com / szzy@szzy99.com
Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
Industry information

當前位置:

首頁 News Industry information

Design of plastic parts for medical device shell

Release time:2021-10-29

Selection of materials

There are many kinds of plastic materials, which have different requirements for different types of products. For the product shell of medical devices, the design should be discussed with the corresponding supervisors to meet the fire prevention or biocompatibility requirements proposed by the regulations.

For monitoring portable products and portable B-ultrasound: it is recommended to use PC materials with fire rating above V2 or ABS PC (c2950, c6600) materials.

For desktop or trolley products: ABS materials with fire rating above V2 are recommended. (anc120 desktop, pa-765a Chimei).


Selection of wall thickness

The wall thickness of plastic parts has a great impact on the quality of parts. If the wall thickness is too small, the forming flow resistance is large, and it is difficult for large and complex parts to fill the cavity, the plastic wall thickness of smaller size should meet the following requirements:

1. Sufficient strength and rigidity;

2. It can withstand the impact and vibration of the demoulding mechanism during demoulding;

3. It can bear enough tightening force during assembly.

Plastic parts are required to have a small wall thickness value, which varies according to the plastic variety and brand and part size. For machine shell parts of medical equipment, the following wall thickness is recommended:

1. ABS, PC ABS, PC, transparent PC, transparent ABS, wall thickness: 2.0-3.5mm

2. Some small appearance parts (such as key cap, lampshade, knob) can be 1.2-2.0 mm

The wall thickness of the same plastic part should be as consistent as possible, otherwise the wall thickness will shrink due to uneven wall thickness.


Draft angle design

On the inner and outer surfaces of plastic parts, design enough draft angle along the demoulding direction, otherwise it is difficult to demould or damage the plastic parts during ejection. In addition, the draft angle is small, and the etched lines will be relatively shallow, which is easy to cause dirty appearance.

For the company's products, it is recommended to adopt the following draft angle: (the design angle is 0.5 degrees higher than the angle required by the grain).

1. For the rear shell of the monitoring instrument, if the travel position is required, it is recommended that the front mold on the side of the travel position is 0-0.5 degrees and the rear mold is 0.5-1 degrees.

The recommended draft angle of the front shell is: according to the thickness of the grain, the front and rear molds are 2-3 degrees respectively.

2. For large ultrasonic products, such as host shell, keyboard shell, front and rear shell of display, and surface shell of blood cell products, it is recommended that the front and rear molds be 3 degrees. For small ultrasonic products, such as knobs, it is recommended that the front mold be drawn 1-2 degrees.

3. When the profile of the side is composed of surfaces, it is necessary to ensure that the angle between the tangent direction of the surface at the parting and the draft direction is not less than the draft angle, otherwise there will be strains near the P.L. surface of the product.


Design of column position

Role of column position:

Usually, the column position of plastic parts is used to support PCBA, fix PCBA or plastic parts themselves, fix electronic components, or connect the front and rear shells of products. One of its biggest advantages is that the height is easy to adjust. Therefore, generally speaking, we should try to use the plane formed by the end face of the column as the supporting surface. The plane formed by several ribs is used as the support surface.

Draft and height of column:

When the height of a column exceeds 10 mm, it is usually pushed out with a cylinder, so the draft angle can be very small, or 0 degrees. The inner hole can be taken as 0 degrees, and the outer surface can be taken as 0.25 degrees. When the height of the column is less than 10mm, inserts can be used on the mold, and the draft angle of the inner hole is 0.5 degrees, and the outer surface is 1 degree. If you want to adjust the height, please mark it on the drawing. When you need mold processing, please consider adjusting the height. Under normal circumstances, the height of M3 self tapping screw column should not be greater than 30 mm. If it is too high, the cylinder needle of the column is easy to bend and deform due to the flow of glue.

Size and size of column: since the column position with a height greater than 10mm is usually pushed out with a cylinder, the outer diameter and inner diameter of the column are limited.


Reinforcement position design

The function of reinforcing rib is to increase the strength of plastic parts and avoid deformation of parts. It is often unreasonable to increase the strength of plastic parts only by increasing the wall thickness. First, it is easy to shrink; Second, the injection molding cost is increased. The stiffener should not be designed too thick, otherwise the root is easy to shrink and should not be too thin. If it is too thin, it is easy to get uneven glue. The recommended thickness is: when the mold is processed into a large nozzle, the thickness of the stiffener root of the part is less than 1/2 of the wall thickness (such as the rear shell of the monitor and the rear shell of the display). The top thickness of the stiffener shall not be less than 1mm. When the mold is processed into a small nozzle, the thickness of the stiffener root of the part should be less than 2/5 of the wall thickness, and the thickness of the stiffener top should not be less than 0.8mm.

About the draft angle of stiffeners: for ordinary stiffeners, the draft angle on both sides can be taken according to the above thickness requirements. For stiffeners with special height requirements, it is best to have 0.1-0.25 degrees on both sides, and then use the stiffeners as inserts. If possible, adding column positions to the stiffeners can help demould.

Stiffener on column position: if the structure allows, the stiffener must be designed for the rubber column. The stiffener on the column position can be much higher than the ordinary stiffener, because it is pushed out together with the column position, and its height direction is 1-3 mm lower than the end face of the column position. At the same time, the stiffener of the column position should be processed symmetrically as far as possible to ensure that the deformation of the column position is as small as possible.


Fillet design

Except for sharp corners, all corners of plastic parts should be rounded as much as possible, because sharp corners of plastic parts are prone to stress concentration and cracking will occur when subjected to force or impact vibration. Even in the process of demoulding, cracks will appear. Generally speaking, we recommend the following principles for machining fillets:

Both ends of the top of the reinforcement, r>1mm.

The square hole in the middle of the plastic part is surrounded by rounded corners, which are greater than 1/4 of the wall thickness of the part.

Make rounded corners on the four corners of the square parts to match the holes above the plastic parts.

The root of the specially stressed column is rounded, about r0.5.


Design of common transparent parts

Transparent materials: there are many kinds of transparent materials in common use, among which transparent ABS, PC and PMMA are commonly used in our design.

The transparent parts commonly used by the company (except biochemical and blood analysis) include lampshade, key cap and decorative sheet (pm7000).

Lens (PM600), etc. due to the poor fluidity of transparent materials, it is easy to produce appearance problems in the injection molding process.

Transparent key caps and other products are easy to produce water marks on the top. Decorative films, lenses and other products are prone to nail lines and serpentine lines near the nozzle.

For the above problems, please pay attention to:

Transparent key cap and other parts: the thickness of the top should be designed to be thicker than the surrounding. If the cavity is too deep, glue should be reduced locally near the nozzle to make the glue flow to the top of the part first, and then to the periphery.

Decorative parts, lenses and other parts: during the design, please reserve a wide (more than 6-8 mm) and thick nozzle position (more than 1-1.5 mm). When processing the mold, try to use a wide fan-shaped nozzle, and the flow channel is short and thick.

Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
久久久噜噜噜久久狠狠50岁-精品一区二区三区av| av网址在线直接观看-黄色av全部在线观看| 日本女优一卡二卡在线观看-欧美大胆a级视频秒播| 欧美精品午夜一二三区-a屁视频一区二区三区四区| 91蜜桃传媒一二三区-日韩欧美国产一区呦呦| 亚洲国产日韩精品四区-dy888午夜福利精品国产97| 欧美精品国产系列一二三国产真人-在线观看国产午夜视频| 久久人妻一区二区三区欧美-国内不卡的一区二区三区| 天天干天天天天天天天-亚洲综合av在线三区| 国产一区二区三区四区五区麻豆-欧美一级在线视频播放| 日本少妇激情一区二区-亚洲自偷自拍熟女另类蜜臀| 欧美精品啪啪人妻一区二区-嫩草人妻舔舔羞羞一区二区三区| 国产精品v欧美精品v日韩精品-国产欧美日韩精品区一区二污污污| 国产精品久久99精品毛片-国产四季高清一区二区三区| 成人av一区二区蜜桃-亚洲色图激情人妻欧美| 国产欧美日韩中文字幕在线-国产伊人一区二区三区四区| 7m视频7m精品视频网站-亚洲综合香蕉视频在线| 日韩精品一区二区三区粉嫩av-欧美亚洲国产中文字幕| 哦啊好大用力欧美视频-麻豆国产传媒片在线观看| 青青操大香蕉在线播放-国产亚洲欧美精品在线观看| 欧美黄色三级视频网站-国产九九热视频在线观看| 乱入一二三免费在线观看-久久精品亚洲精品国产色婷婷| 久艹在线观看视频免费-人妻偷人精品一区二区三区| 欧美一级二级三级在线看-日韩精品欧美嫩草久久99| 麻豆久久国产精品亚洲-日本理论中文字幕在线视频| 国产成人精品免费视频大全办公室-亚洲欧美日本综合在线| 欧美日韩亚洲1区2区-黄污视频在线观看不卡| 在线视频成人一区二区-亚洲另类中文字幕在线| 亚洲产国偷v产偷v自拍性色av-亚洲欧美日韩国产三区| 国产免费一区二区三区不-日本少妇免费一区二区三区| 久艹在线观看视频免费-人妻偷人精品一区二区三区| 欧美日韩黑人在线播放-51在线精品免费视频观看| 亚洲产国偷v产偷v自拍性色av-亚洲欧美日韩国产三区| 亚洲视频一区二区三区免费-国产一级黄色大片在线| 交换朋友的妻子中文字幕-日本美女8x8x8x8| 性激烈欧美三级在线播放-久久中文字幕人妻少妇| 欧美一级一线在线观看-亚洲一区二区亚洲三区| 国产美女网站在线观看-国产精品亚洲综合网69| 精品一区二区三区av在线-欧美黑人巨大精品一区二区| 国产传媒中文字幕在线观看-午夜福利视频在线播放观看| 男女做爰猛烈啪啪吃奶在线观看-人妻连裤丝袜中文字幕|